Sekonic SR-6500 Betriebsanleitung

DIC579K10 30 50 70 90CC0797100Operating manualOperating Manual7-24-14, Oizumi Gakuen-cho, Nerima-ku, Tokyo 178-8686, JapanTelephone: +81-3-3978-2375

-9-Before using2. Strage bag (Transparent plastic bag)Stacker unit (Option)* See the installation manual for components to be used for installatio

-99-Cleaning proceduresMain body unit1. Turn the power off and remove the power cord from the outlet.2. Grasp the lock lever to release the lock, a

-100-Stacker unit (when stacker unit is installed)1. Turn the power off and remove the power cord from the outlet.2. Open the front door of the stac

-101-5. Close the jam release lever.6. Clean the remaining three parts in the same manner as in steps 3 to 5.Jam release lever7. Close the front do

-102-Service scheduleFor stable operation of this device, regular replacement of components is required.See the following table, and contact us, or th

-103-Component name NumberReplacement reference(counter number)RemarksDriving roller / 1 1 500,000 or 3 years -Driving roller / 2 2 500,000 or 3 years

-104-External diagram(SR-3500)Front view575371.7292.6227Top view36525556.3Rear viewLeft view Right view(Unit : mm)External diagramSR-3565(E).indd 10

-105-External diagram (SR-6500,SR-3500 when stacker unit is installed)365490800(Unit : mm)Front viewTop viewRear viewLeft view Right viewExternal diag

-106-Setting menu Setting item Setting valueOperation ModeSR-3500 mode , SR-600 modeSR-6500 mode , SR-9000 mode*1 *2Setting of InterfaceDevice ID0

-107-Setting menu Setting item Setting value *1 *2Setting ofPrinter(only when the stacker unit and the printer unit are installed)Printer Control Vali

-108-Setting menu Setting item Setting value *1 *2Test ModeFeed Test 1 Start , Stop O OFeed Test 2 Start , Stop O OMarking Test(only when the stacker

-10-Before using(SR-6500)Before using the device, check if all of the following items are included in the package. If components are missing or damage

-109-Error displays and countermeasures 1. Errors(1) Hardware errors [Main body unit]Error Explanation Code SolutionMemory error 1 Internal me

-110- [Reading unit]Error Explanation Code SolutionCommunication errorLine error occurred between the device and the front side reading unit.B1 NoneLi

-111-Error Explanation Code SolutionCommunication errorLine error occurred between the device and the barcode unit.C1 NoneInternal com. errorBarcode u

-112-(2) Transmission errorsError Explanation Code SolutionCommand errorA non-specifi ed command code was received.F4Press the CLEAR switch (or execut

-113- [Stacker unit]Error Explanation Code SolutionJam at printer printing start detection sensorA paper jam occurred at the printer printing start de

-114-Error Explanation Code SolutionHopper stopsInterlock on the side of the paper-feeding roller operated.R1• Release the interlock switch.• Press th

-115- [Main body unit]Error Explanation Code SolutionForm left in hopperA sheet remained in the paper feeding detection sensor.T1• Remove the remaini

-116-OMR glossaryColumn and Row Mark frames are in columns, timing marks are in rows.1stcolumn2ndcolumn3rdcolumn4thcolumn5thcolumn1st row2nd row3rd r

-117-Timing control type If paper has pre-printed timing marks, the scanning area (reading area) of targeted mark frames will be determined by such t

-118-Direct under type If paper has pre-printed timing marks, the scanning area (reading area) of targeted mark frames will be determined by such tim

-11-Power cord list for EuropeAs stated on page 7 of this manual, the machine includes a representative variety of power adapters. If none of the incl

-119-(5) Colors that can be used as dropout colors differ depending on the model, but with some models, even regular ballpoint pen ink drops out and

-120-Writing implements Readable marks and unreadable marks depend on the writing instruments used. This can also differ according to the light sourc

-121-Mark to mark type If paper has pre-printed timing marks, the scanning area (reading area) of targeted mark frames will be determined by such tim

-i-AppendixSheet creation referenceYou can use paper that you make yourself with this device in addition to the optional paper that we offer. If you

-ii-(8) Clear zones Do not print in colors other than dropout colors 0.8mm around reading zones and 0.8mm from timing mark longitudinal ends. Reading

-iii-(13) Paper dimensions [Direct under type sheet]Note 1) Timing mark width: maximum width of c is 12mm.Note 2) Maximum number of rows indicates t

-iv- [Direct under type card (0.25” IBM card size)]Standard size 187.320.2A0.2A0.2A82.550.86 or moreMinimum 15 or more3.5±0.1Standard sizeGeneral tol

-v- [Timing control type sheet]Note 1) Timing mark width: maximum width of c is 12mm.Note 2) Maximum number of rows indicates the number of timing m

-vi- [Mark to mark type sheet]Mark frameSheet vertical length (L 1. 3xW)0.3A0.3A0.3A4 or moreSheet horizontal length (W)Pitch (P) x (row-1)Do no

-12-WarrantyThe cost-free warranty period for this product extends for one year after delivery.The company will repair malfunctions arising during thi

-vii- [Mark to mark type card (0.25” IBM card size)]Standard size 187.320.2A0.2A0.2A82.550.89 or moreMinimum 19 or more3.5±0.1Standard sizeGeneral to

-13-Precautions For UseHandle the device with the following points in mind to enable full use of its functions.• Precautions regarding installation D

-14-Handling precautions (continued)(11) Do not apply strong loads to the tray, as it may bend or break.(12) Because the aligning roller section has

-15-Precautions For Use(14) Make sure to observe the following points when you handle the device and USB cables. Otherwise, mechanical failure or da

-16-Names of parts(SR-3500)Names of partsPaper weight setting dialInterlockSide guidePaper feeding table(hopper)Side guide knobDisplay panel (LCD)Oper

-17-Names of parts(When stacker unit is installed)SR-6500 is equipped with the stacker unit standardly Paper weight setting dialInterlockSide guide k

-18-Operating panel functions and operating instructionsThe operating panel has fi ve kinds of switches.The switches don’t work while the machine is p

-1-IntroductionThank you very much for purchasing our product.Please read the operating manual before using this product, and be sure to use it proper

-19-Product specifi cations(SR-3500) Sensor Reading Single sided, [double-sided] (* You need an optional back-surface reading unit for

-20-Product specifi cations(SR-6500) Sensor Reading Single sided, [double-sided] (* You need an optional back-surface reading unit for

-21-OperationPreparation (SR-3500)1. Protecting tapes are attached to the main device in the following positions to protect it from vibration and sh

-22-4. Connect the power cord to the main device.5. Connect the power cord to the power outlet.Operation PreparationSR-3565(E).indd 22SR-3565(E)

-23-Operation PreparationOperationPreparation(when stacker unit installed)1. Install the main tray on the main body unit. Hook the tabs on the end

-24-Operation Preparation4. Connect the power cord to the power outlet.SR-3565(E).indd 24SR-3565(E).indd 24 2007-8-16 10:18:522007-8-16 10:

-25-Turning power on1. Turn the power on. The following message appears on the display panel (LCD).2. OMR is initialized.3. The motor and other co

-26-Loading paper1. Load paper with the timing marks on the left side of the hopper. The hopper is set to drop when the power is turned on, but if i

-27-Note)1) The aligning roller is fi xed with the magnet.Check that there is not a gap and a fl oating on the adsorption aspect. In case of a certain

-28-Setting paper weight1. The device is equipped with a function to detect double-feeding (DF) errors. Conduct [Paper Weight]*1 according to the t

-2-Table of contentsSafety precautions ... 5Before using

-29-Marking instructionsMarks readable by this device are as follows.1) Mark size: 0.5 x 3mm or more (standard mark)2) Readable writing instruments:

-30-Connecting to a computerThis device is equipped with USB and RS-232C interfaces.When connecting the OMR,the connection with USB in order to show t

-31-USB1. Operating mode Select the SR-3500,SR6500 mode as the operating mode.(1) Press the MENU switch to enter the menu mode.(2) Use the UP and DO

-32-Connecting to a computer USB2. Interface settings(1) Press the MENU switch to enter the menu mode.(2) Use the UP and DOWN switches to select the

-33-Connecting to a computer RS-232C(SR-3500)(SR-6500)RS-232C1. Operating mode Select the SR-600,SR-9000 mode as the operating mode.(1) Press the

-34-Connecting to a computer RS-232C2. Interface settings2-1. Setting baud rate(1) Press the MENU switch to enter the menu mode.(2) Use the UP and

-35-(3) Use the UP and DOWN switches to select [Character Bit Length] setting, and press the FEED/ENTER switch. (“” mark fl ashes in the fi rst column

-36-2-4. Setting stop bit(1) Press the MENU switch to enter the menu mode.(2) Use the UP and DOWN switches to select the following parameters, and p

-37-(4) Use the UP and DOWN switches to set the value.2-6. Setting character code(1) Press the MENU switch to enter the menu mode.(2) Use the UP and

-38-Data reading settingsThis section explains how to change various sheet-reading settings.All settings can also be made using computer commands.Set

-3-Stacker settings ... 52Printer settingsPrinter con

-39-Setting reading methodSetting mark-reading method.There are six kinds of reading methods: “Top-end timing control type,” “Bottom-end timing contr

-40-Setting magnifi cation when timing control types are selected1. Press the MENU switch to enter the menu mode.2. Use the UP and DOWN switches to sel

-41-SR-3500SR-6500min. densitylevelSR-600SR-9000modemin. densitylevelSR-3500SR-6500min. densitylevelSR-600SR-9000modemin. densitylevelSR-3500SR-6500mi

-42-Setting density balanceYou can set the density balance level when using the SR-600/SR-9000 operating mode.Density balance can be set so that when

-43-Setting reading sideYou can set the reading side when the optional back-sided reading unit is installed.The reading side can be set to either “si

-44-Setting hopper modeSetting the hopper mode for reading sheets.The hopper mode can be set to either “ADF” or “manual feed.”If you set it to “manua

-45-3. Use the UP and DOWN switches to select [Wait Time for Form] setting, and press the FEED/ENTER switch. (“” mark fl ashes in the fi rst column of

-46-Setting paper weightSet detection sensitivity In the same paper weight as seat of use to detect double-feeding errors.Paper weight can be set acc

-47-Setting Paper hold(SR-3500)You can set paper hold setting when using SR-600 operating mode.When paper hold setting is done, after reading, withou

-48-Error detection settingsError detection settings for this device differ depending on the operating mode. See the following table for settings.All

-4-Barcode readable area ... 92Barcode reading position adjustment

-49-4. Use the UP and DOWN switches to select individual error detection setting values. (See the previous table for setting values.)5. Press the FE

-50-Buzzer settingsYou can set the device to either use the buzzer or not use it.If you set it to use the buzzer, you can set the volume and tone.If y

-51-Buzzer sound adjustment1. Press the MENU switch to enter the menu mode.2. Use the UP and DOWN switches to select the following parameters, and p

-52-Stacker go out directionsetting values• Main • SelectStacker settings (when stacker unit is installed)You can set the paper discharge directio

-53-Printer settings (when stacker unit or printer unit are installed)A character is 12 x 9 pixels.Though character height is fi xed (about 3mm), width

-54-SR-3500,SR-6500 mode1. Character size setting The width of a character can be increased in 0.8mm increments between 3.2mm and 6.4mm.(1) Press t

-55-Printer settings SR-3500,SR-6500 mode3.2mm6.4mm2. Character interval setting The space between printed characters can be increased in 0.1mm in

-56-(5) Press the FEED/ENTER switch to save the setting value into memory. (The fl ashing “” mark disappears from the LCD.)(6) Keep pressing the CLEAR

-57-Printer settings SR-600,SR-9000 modeSR-600,SR-9000 mode1. Character size setting The width of a character can be set in fi ve increments.(1) P

-58-Printer settings SR-600,SR-9000 mode2. Character magnifi cation setting Width can be magnifi ed between 1 to 15 times. Character width = size x

-5- Safety PrecautionsThese “Safety Precautions” pages list various symbols for ensuring safe operation of this product so as to prevent users or othe

-59-3. Character interval setting The space between printed characters can be increased between 0 to 99 pixels. The actual character interval (in mm

-60-Printer settings SR-600,SR-9000 mode [Setting example 1] When the size is set at 3.2mm, the magnifi cation is 1, and the interval is 0 pixel.

-61-Barcode settings (when barcode unit is installed)You can set the barcode control in SR-3500,SR-6500 mode.Barcode control1. Press the MENU switch

-62-Low power consumption settingsThis device can be set to reduce power consumption in standby mode.The low-power consumption settings make the devic

-63-Standby duration1. Press the MENU switch to enter the menu mode.2. Use the UP and DOWN switches to select the following parameters, and press th

-64-Displaying various informationThis section explains how to display various setting information.Displaying the versionThis displays the versions o

-65-Displaying front side reading sensor settingsThis displays the settings for “sensor pitch” and “sensor type” for the front side reading unit in t

-66-Displaying back side reading sensor settingsThis displays the settings for “sensor pitch” and “sensor type” for the back side reading unit in thi

-67-Displaying optional unit settingsThis displays the settings for an optional unit installed in this device.1. Press the MENU switch to enter the m

-68- Displaying total countThis displays total count in this device.1. Press the MENU switch to enter the menu mode.2. Use the UP and DOWN switches to

-6- If any foreign matter should enter inside, immediately turn the power switch off and remove the power plug from the outlet. Then, contact the sa

-69- Displaying serial numberThis displays serial number of this device.1. Press the MENU switch to enter the menu mode.2. Use the UP and DOWN switche

-70-Operating testsThis section explains operating test procedures.Feed test 1This test reads the check sheets included in the package to test if the

-71-Feed test 2This test reads the check sheets included in the package to test if the device reads them properly.Even if the device doesn’t read som

-72-Printer testThe test characters is printed on the fed sheet and the sheet will be discharged. (This test will be conducted only when stacker unit

-73-Printer jet testThis test is done when the printing of sheets is not possible, is not clear. ( This test will be conducted only when stacker unit

-74-OptionsStacker unitSR-6500 is equipped with the stacker unit standardly, SR-3500 is equipped with it optionally.Stacker unit specifi cations (prin

-75-Stacker unit (printer) preparation1. Turn the power off and remove the power cord from the outlet.2. Open the front door of the stacker unit.Fr

-76-5. Lift the cartridge case lever and insert an ink cartridge.Note)Align positioning pins (2 places) of the ink cartridge with the positioning hol

-77-8. Tighten the printer fi xing screw and connect the printer connector.Fixing screwConnectorPrinter9. Close the front door of the stacker unit.Fr

-78-Printing position adjustment1. Turn the power off and remove the power cord from the outlet.2. Open the front door of the stacker unit.Front do

-7- Caution Do not put heavy things on the device. Otherwise, it may fall or collapse, resulting in injury. Do not place the device in an unstabl

-79-5. Loosen the cartridge case fi xing screw, move the cartridge case according to the desired printing position, and tighten the screw to secure it

-80-8. Close the front door of the stacker unit.Front door9. Connect the power cord and turn the power on.10. Execute printer test ( See P.72). *

-81-Clearing paper jams1. Open the front door of the stacker unit.2. Open the jam release levers (4 levers) or turn the jam-removing knob to remove

-82-Stacker unit precautions for use(1) Make sure to tightly close the jam release levers and the front door. Loose levers or a loose door may trigg

-83-Back side reading unitIf you install a back side reading unit in the device, both sides of a sheet can be read.When installing the back side readi

-84-Printrer unitPrintrer unit is a optional equipment with SR-3500.Printer unit specifi cations Printing location Prints on top surface of fed shee

-85-1. Printing after reading marks The printable area is a maximum of 230mm from the bottom edge of a sheet. [When sheet size is (L > 233)mm]2m

-86-Printer unit preparation1. Turn the power off and remove the power cord from the outlet.2. Remove the carrier cover.3. Lift the cartridge case

-87-Printing position adjustment1. Turn the power off and remove the power cord from the outlet.2. Remove the carrier cover.Carrier cover3. Loosen

-88-6. Execute printer test ( See P.72). * If the printing position is misaligned, loosen the cartridge case fixing screw, adjust the cartridge cas

-8-Before using(SR-3500)Before using the device, check if all of the following items are included in the package. If components are missing or damaged

-89-Printer unit precautions for use(1) Use ink cartridges before their expiry dates.(2) Under the following conditions, remove the ink cartridge fr

-90-Barcode unit / V • barcode unit / HIf you install a barcode unit in the device, barcodes on paper can be read.Barcode unit specifi cationsBarcode

-91-Barcode unit / H (horizontal feeding) Reading direction Horizontal feeding (bar direction is perpendicular to sheet feeding direction) Codes J

-92-Barcode readable areaThe barcode readable area differs depending on the kind of barcode unit.1. Barcode unit / V (vertical feeding)0mm 50mmTimin

-93-2. Barcode unit / H (horizontal feeding)0mm 20mm 224mm 0mm12mm40mm or more10mm or more65mm or moreClear areaClear areaClear areaClear areaReadin

-94-Barcode reading position adjustment1. Turn the power off.2. Remove the carrier cover.Carrier cover3. Loosen the barcode unit position fi xing s

-95-5. check reading using a diagnostic utility. * If a reading error occurs, the barcode reading position may be misaligned, so make an adjustment.

-96-Barcode unit precautions for use(1) When applying barcode stickers, etc. on a sheet, make sure that sheet thickness with stickers is 0.25mm or l

-97-CleaningDirty rollers, reading lenses, and sensors can cause various operational errors. Clean them regularly using the following procedures. Clea

-98- Stacker unit (when stacker unit is installed)CleaningDriving rollersSlave rollersSlave rollersSlave rollersSlave rollersPaper discharge roller